Once the base and the activator have been mixed then it initiates the chemical reaction that causes it to cure. So once the two components have been mixed you have a limited amount of time to apply it before it has hardened too much. Often it is recommended to keep stirring at different intervals throughout to give you some extra time to apply the whole mix. Mix Part A on its own with a mixing paddle attached to an electric drill for about 1 minute before adding ALL of Part B and continue to mix for another 90 seconds, keeping the paddle in suspension to avoid mixing air into the unit. Having been in the trade for many years, Jez is an absolute master at restoring old wooden floors and installing new ones with a quality of workmanship that is second-to-none. You can combine 5L (30m²) and 2.5L (15m²) for areas which are not multiples of 30m² in size and more than one coat is required. For example, to cover 45m² with 2 coats use 1 x 5L and 1 x 2.5L for the first coat and same again for the second. If you have any questions please let us know. New concrete should be at least 2 months old and always washed with floorsaver Floor Etcher to reduce alkalinity and to remove any weak, loose cement deposits.

The winner of our June #showusyourproject competition is a local flooring specialist, @purtfloor of Hartshill, Stoke-on-Trent. The right choice for garage floors as it'll stand up to hot tyres and resist automotive fluids and chemicals that ruin ordinary paint. Safe and easy to use, virtually solvent free (extremely low VOC) for hygienic areas. Anti slip epoxy floor coating is in excellent demand being also known as one of the most robust and durable paint products. It is a set of two parts – a colourant and a hardener, which you can comfortably mix to obtain the desired consistency. Thus, epoxy floor paint is a practical solution for painting large areas of commercial and industrial premises. The formulation is easy to apply and further use. Everyone can paint the surface with epoxy floor paint without specialised skills, getting an even multifunctional coating with many functional properties. Feel free to use the brush, roller, or spray to cope with the task effortlessly.A: We do not recommend our products going over self levelling compounds. However, some manufacturers say that they can be painted, so it's best to speak to Sika and ask them. They may say that a two part, water based epoxy resin can be used, if this is the case then ours would fit the bill but we couldn't guarantee anything. This product should NOT be split. Taking smaller quantities from each tin, even if measured correctly, may cause issues with activating. The floor was prepped and them primed with the epoxy sealer coat, before being finished with the top coat in light grey. If you think you may have gotten the ratios wrong then there are a few ways to figure it out by the issues you’re having with the finish.

Epoxy floor paints are suitable for a thoroughly sanded primed surface and also can be applied directly on an unprepared coating. However, experts recommend pre-cleaning, degreasing, and drying the top layer. Careful preparation is essential to ensure good adhesion to smooth materials such as metal or plastic. Buy #1 Epoxy Resin Floor Paints Online If you enjoy our blog and think you can help give a small business a boost, please feel free to share it to your friends or any classic car forums that you might be part of. The cured final coat is ok for foot traffic. Cars and heavy objects, however, should be left off the new coating for the first 48 hours and chemicals including water should not be introduced for the first 7 days (Full chemical cure). This product is NOT UV stable therefore can discolour when exposed to regular sunlight. For areas with plenty of repeated sunlight, please coat with a coloured UVR coating such as Resincoat Chemical Resistant UVR Floor Coating for a UV stable finish.If the specified induction time is not followed then it can lead to further issues, such as: a lower gloss level, yellowing, blushing, colour variation and more. Common mistakes: Applying to very weak, crumbly or contaminated concrete since it may not be possible to prepare it well enough for the Epoxy Floor Paint to perform. The datasheets not only give you instructions on how best to use and apply the products, but they also give crucial information about mixing two components. The three main things to look for are: the length of time recommended to mix the product; the potlife after mixing the two components; and also whether or not an induction time is needed. Mixing the product: Q: I’ve levelled my floor with Arden k301 which I chose because it is suitable for overpainting with resin paint. As dictated by normal good painting practice. Do not apply if the temperature is likely to drop below 10°C during application or during the drying process. In confined spaces provide adequate ventilation during application and drying.

For greasy or previously painted floors, clean with floorsaver Cleaner & Degreaser, scraping off any loose paint, dust or dirt. Lightly sand glossy paint to dull down the shine and roughen it up. If the induction time was not followed then there are a good few issues that can arise. They are mostly aesthetic, but nonetheless problematic. After the products are mixed, and the chemical reaction has started, sometimes an exothermic reaction happens and the paint gets hot. But don’t worry, that’s perfectly normal. As long as the mixing itself was done slowly it’s all fine. Slip resistance can be enhanced by incorporating our medium grade anti-slip aggregateadditive into the system. Scatter the aggregate onto the wet first coat, this should be allowed to dry, then the loose particles brushed away before applying the second coat.

All surfaces should be clean, dry, sound and free from contaminants. Concrete - power floated, granolithic and smooth surfaces should be roughened first to provide a good "key" for the paint. This can be done mechanically by abrading or blasting, or chemically using Coo-Var Acid Etch. These processes will have the advantage in addition to preparing the surface of also removing dirt and laitance. For greasy floors with heavy oil residue clean thoroughly using a suitable degreaser scraping off any dust or dirt and then prime with Resincoat Oil Tolerant Primer Of all of the mistakes, this is the most difficult one to fix. If you have applied one of the components, then applying the other one over the top, or trying to mix it on the surface won’t fix it. The whole thing would have to come up and start again. So you really need to make sure you get this part right the first time! To ensure fair pricing, we split colours into ‘Price Bands’ to group together similar priced colours. If you wish to search for the cheapest tinted colours, always select Price Band 1.

I am afraid i would recommend finding a DPM product to apply first. This can be an epoxy damp proof membrane or paintable style coating rather than a traditional DPM system. Provided our water based epoxy coating can be painted on top, this woud still be a very practical solution. Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour Give a good stir with something wide, like a wooden batten or a paint stirrer. If you use an electric paint mixer, also scrape around the sides and bottom of the tin to make sure it's all mixed in.Our Epoxy Garage Floor Paint is the number one choice for concrete floor paints in the UK as it protects and seals whilst offering an attractive, decorative, professional finish. This product is part of the Resincoat High Build Epoxy Range, heavy-duty, solvent free epoxy floor coatings, possessing exceptional abrasion and chemical resistance. We proudly manufacture all our resin products and floor paints in the UK, guaranteeing the highest quality finish. Buy in confidence from Resincoat an ISO 9001 accredited company.