Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) They are two identical-looking units, but one is the router (model SXR30), and the other is the Satellite (SXS30). Without the label on the router, you can't tell them apart from the front.

It is clear as "If you do need help, the support that Netgear provides is excellent. “, is an outright lie. Their support is a call center oversees that simply knows a set number of SIMPLE troubleshooting and that is it. UBIFS (ubi0:3): media format: w4/r0 (latest is w4/r0), UUID 189A65E6-F6C4-4E45-98EE-DAFB854E174B, small LPT model wlan: [8522:I:ANY] wlan_cfg80211_set_hwaddr: 6162: wlan_cfg80211_set_hwaddr :9a:a6:7e:63:2d:23 ret: 0 |wlan: [2795:I:ANY] ieee80211_autoselect_infra_bss_channel: 3995: ACS started: vap:0xffffffc02b1b8000

Can't find what you're looking for?

of_get_named_gpiod_flags: parsed 'sd-ldo-gpios' property of node '/soc/sdhci@7864900[0]' - status (0) wlan: [9422:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath11 : clone params: 0x00000001 wlan: [7879:I:TIF] init_deinit_add_11ax_modes: 1467: hw_mode_id = 4 phy_id = 0 wireless modes = 397f9001 wlan: [7818:I:TIF] ol_ath_pdev_regdmn_init: 7404: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0

Doing that entirely undermines the purpose of MESH wireless networking, but with the limited bandwidth of the Mini, it might be the best policy. Anyone have any experience to tell me this should or should not be happening? I'd much prefer to use the Pro system - both because its several hundred less than I paid for the consumer system and because I have a Firewalla purple on the way that I wanted the option for VLAN setup. But there is no way that's worth it if the performance isn't on par with what we are getting from the consumer model - which is giving us - for the first time in this house - wifi that allows us to use the network the way we want. wlan: [7818:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc0354a4c00 ic->ic_wrap_com=ffffffc0354a4c00 &wrap_com->wc_devt=ffffffc0354a4c00 wlan: [7818:I:ANY] ieee80211_cfg80211_radio_attach: 11017: ic: 0xffffffc033000880, wdev: 0xffffffc033010a70, wiphy: 0xffffffc03559f2a0, netdev: 0xffffffc033000000 So In the web interface > Advanced > Advanced Setup > mDNS Gateway, I enabled mDNS Gateway and added the following policies:Originally I tried using the last release artifact from your repo, but when I tried that I had wired ethernet but no Wireless: [ 6.437609] ath11k c000000.wifi: failed to fetch board data for bus=ahb,qmi-chip-id=0,qmi-board-id=255,variant=Netgear-SXS80 from ath11k/IPQ8074/hw2.0/board-2.bin Where this option differs from the SXK80 hardware is that the Ethernet switch components had link aggregation and 2.5 GbE Ethernet on that design, but those features are both missing from the SXK30.