Brasso Metal Polish, 175 ml

Product Information

It has been used to polish CDs, DVDs, screens, and pools to repair scratches. It is a mild solvent and an extremely fine abrasive, so when applied to the reflective surface of the disc and rubbed radially (in straight lines between the edge and centre), it can smooth scratches and reduce their effect. [8] [9] [10] Using Brasso to clean and polish grotty metal surfaces is super easy, and doesn’t cost you a fortune! When you’re done using your Brasso you need to store it away in a safe place, that is out of the reach of children and pets.

Regularly wipe/buff the already treated areas with an additional clean cloth to see how you’re polishing exercise is going.Brasso is a metal polish designed to remove tarnish from brass, copper, chrome and stainless steel. It is available either directly as a liquid or as an impregnated wadding pad. Don’t leave a job half done – Once you start using Brasso to clean a surface, you should finish cleaning the surface in one go. If you leave the surface to dry, you’ll have Brasso residue. And as a consequence of this, items might not look shiny and evenly cleaned.

Brasso can be bought from most hardware stores and supermarkets. You’ll typically find it near to, or in, the cleaning products aisle. Continue to do this until the patch is clean – you might need to apply more pressure to certain grimey patches. Below you’ll find steps on how to use Brasso in both liquid and wadding form. Skip to the section that applies to the Brasso you’ve bought. General tips to think about before you start using Brasso:Note: You’ll likely have to use more Brasso for tougher, dirtier spots! And if your Brasso cleaning cloth goes dry, add more liquid Brasso to it or use a new piece of wadding. Benefits of using Brasso Brasso, if used correctly, will naturally be worked into a surface, and any residue will be buffed away by a clean cloth at the end of the exercise.

Although, if you’ve used an appropriate amount of Brasso for the surface you need to clean, and you’ve worked the Brasso into the item and buffed it as well, there shouldn’t be any need to remove the Brasso with water. You should remove Brasso from small nooks before it dries– Use a small, slim tool that’s wrapped in a cloth to tease the excess Brasso from crevices. Leaving the Brasso to dry will just make it harder to remove, and you might not end up with the sleek finish you were after if there’s Brasso residue all over the place. Always wear gloves and a mask– Brasso can cause skin irritation and inhaling the fumes may lead to drowsiness. Brasso is a well-known metal polisher, that can be used to polish, remove tarnish and clean up chrome, stainless steel, copper, and of course, brass. Railway And Canal Commission." Times [London, England] 22 May 1913: 22. The Times Digital Archive. Web. 13 Sept. 2018.

Tip: If you’re using liquid Brasso, always pour the liquid from the can onto a clean cloth. Do not hold a cloth over the mouth of the can because this transfers dirt into the can. This then contaminates and weakens the Brasso inside the can. How to clean with wadding Brasso:

Brasso has been used by watch enthusiasts to polish scratches out of acrylic crystals on watches. [12] Keep an eye out for a blue and white striped pot that has a big red label on the front, with the name ‘Brasso’ on it. Gently rub a piece of Brasso wadding onto the surface you want to clean to perform a small patch test – make sure the Brasso doesn’t mark or stain the surface you’re about to polish.

If you’ve got some stubborn Brasso that needs to be cleaned away, follow these steps to get rid of the troubling Brasso: For the historical county of the Kingdom of Hungary, see Brassó (county). For the county seat thereof, see Braşov. In 2010, Brasso brought out a new product, Brasso Gadgetcare. Gadgetcare is a versatile, non-abrasive gel that can be used on everything from LCD TV screens, laptop screens, computers, smart phones and PDAs. The plastic bottle is 50ml and is sold with a microfibre cloth. If you do have Brasso residue leftover, either keep buffing it off the surface or use a clean cloth to remove it.